background image

 

10

OPERATING YOUR BEER DISPENSER

 

 

¾

 

Setting The Temperature 

 To start, turn the temperature control knob to the maximum setting (6). Allow 
the unit to run for 24 hours for the unit to cool properly. You may then adjust the 
temperature to the desired setting.  
 
In average room conditions of 70°F (21 ºC), set thermostat knob position 
between “4” and “5. 
 
To turn off the Beer Dispenser, rotate the control knob to the “OFF” position. 
 
Note: To accurately measure the temperature of liquid in the unit, place a cup of water  
In the front corner, and place a liquid thermometer in the water. 
 
During the summer when temperatures are warmer, we recommend that you adjust the control to a 
cooler setting. 
 
The time it takes to reach your desired temperature depends on the beer keg size and the room 
conditons where the beer keg cooler is located. Normally, on setting of 6, it takes no more than 36 
hours for a 1/2 barrel keg to cool down if the ambient temperature is 60°F to 75°F. 
 
The more beer there is, the longer it will take to cool down. 
 

Automatic Defrosting 

There is no need to defrost the Beer Dispenser. Defrost water collects and passes thru the drain 
outlet in the rear wall into a tray located above the compressor, where it evaporates. 
 
 

 

 
 
 
 
 
 
 

¾

 

Converting To An “All Refrigerator” 

1.  Turn off the control knob to the “OFF” position. 
2.  Close the main valve on the CO

2

 cylinder. 

3.  Close the secondary shut-off valve on the regulator pipe. 
4.  Close the connection between the beer keg and the keg coupler. 
5.  Drain any remaining beer from the lines. 
6.  Disconnect the beer line and CO

2

 air line from the keg coupler 

7.  Remove the beer keg. 
8.  Remove the keg coupler. 
9.  Disconnect the air line from the CO

2

 cylinder. 

10. Remove the CO

2

 air line from cabinet plug 

11.  Replace the air line rear cabinet plug 
12.  Remove the beer tower. Also pull the beer line thru the top of the cabinet 
13.  Replace the top cabinet plug 
14.  Adjust temperature as desired. 

 
 
 

 

NOTE:  

If the unit is unplugged, power lost, or turned off; you must wait 3 to 5 

minutes before restarting the unit. If you attempt to restart before this time delay, 
the Beer Dispenser may not start. 

Summary of Contents for Vissani MCKC490S















Reviews: