manualshive.com logo in svg

VisionxIP VxIP 9211, User Manual

Share
Download
VisionxIP VxIP 9211 User Manual Download Page 10

 

Mail: 

[email protected]

 

Web: 

www.visionxip.com

 

 

10 

Hardware Installation 

You can use bundled screws and the device cover to secure this camera to the ceiling 
(strongly recommend this type of installation for the best effect) or place horizontally 
(this camera has image inversion function, please refer to the “Control Panel” 
section). 

Note 1: If you want to hang this product from the ceiling, do not fasten it to the asbestos board on 

a light metal frame. The fragile asbestos board cannot secure this product properly and 
may cause it to drop, possibly causing injuries to personnel or damage to the product. It 
is best to secure this product to a sturdy flat surface made of wood, cement, metal, etc. 
The bundled screws are applicable to wooden boards. To secure it to other materials, 
please choose the appropriate screws. 

Note 2: When using the screws to secure this product to the ceiling, be careful not to drop the 

screws and hurt your eyes. 

Note 3: Pay attention to the horizontal angle when installing this product, over tilting or a 

vertical angle may cause abnormal operation of the camera lens and damage the 
transparent cover. 

Note 4: After setting this product, you can now fasten it to the ceiling. 

 

 

 
 
1. Connecting the network cable 
 

Connect one end of the network cable to the network connector on the rear panel. 
Connect the other end to the subscriber network environment. 

 

 

 

2. Connecting the power source 

Connect the bundled power supply to the power connector. Then connect the power 

Summary of Contents for VxIP 9211














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands