Vision & Control vicosys 5300 Instructions For Use Manual Download Page 53

Page: 53 / 60

vicosys

5300

Commissioning

6.4.1 Create a LAN connection / direct connection

1. Start the operating software vcwin on the PC.
2. Open the window

Communication Parameters

by calling

Communication >

Interface

The settings made here are used during each connection setup.

3. Switch to the TCP/IP tab.
4. With the [Search] button, all available devices, on the same subnet, are

displayed (UDP broadcast to all participants).

5. Select the appropriate device.
6. Optionally, you can also enter the name and IP address of your device.
7. Click the [OK] button to accept the values.

ADVICE

Factory setting: The device searches for a DHCP server during initialization

in the LAN. If no DHCP server is available, a static IP address is used

(default: 192.168.3.180).
If the device can not be found, a monitor can be connected and the IP can be

read off during initialisation.
The settings can be changed via vcwin.

999.994.347.10-en-2.7

Summary of Contents for vicosys 5300





























































Search results

Summary of Contents for vicosys 5300

Reviews:

Brands by name

Popular brands

Vision & Control vicosys 5300, Instructions For Use Manual

Search results

Summary of Contents for vicosys 5300

Reviews:

Brands by name

Popular brands