manualshive.com logo in svg

Vision & Control vicosys 5300, Instructions For Use Manual

Share
Download
Vision & Control vicosys 5300 Instructions For Use Manual Download Page 44

vicosys

®

 5300

Commissioning

6.3.6 Connect the digital I/O interface (Digital I/O card ADDI-

DATA)

NOTICE

Damage of the outputs through inductive loads

•

With induced loads the outputs have to be switched with a free-wheeling

diode anti-parallel to the load.

NOTICE

Destruction caused by potential differences

•

The ground potential (GND) of the digital inputs and outputs of the device

must be connected to the ground potential (GND) of the control voltage of

the device to be controlled.

Connecting

Die zum Anschluss benötigten Komponenten erhalten Sie als Zubehör. 

see

"Accessories for the option Digital I/O card ADDI-DATA", page 12

Connect the 37-pin D-Sub connector of the device's I/O expansion card to the

process environment using one of the following two variants:

•

I/O cable with 2 x Sub-D and terminal board

•

I/O cable with 1 x Sub-D and open cable end

44

999.994.347.10-en-2.7

© Vision & Control GmbH 2021

Summary of Contents for vicosys 5300





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands