Vision & Control vicosys 5300 Instructions For Use Manual Download Page 52

Page: 52 / 60

vicosys

5300

Commissioning

Switch on the device

5. Switch on the supply voltage (24 VDC).

The device boots automatically.

ADVICE

Before switching on the device, connect a monitor to the DVI interface.

You can observe the boot process.

6.4 Creating a connection

The devices is configured and parametrised with the operating software

vcwin. The current version can be found on the homepage

http://www.vision-

control.com/products

in the path

Vision Systems > Operating Software

The Software must be installed on the PC.

Start and terminate vcwin

The vcwin software is started by either double-clicking on the vcwin icon or

from the Windows start menu by calling

Start > Programs > Vision & Control

GmbH > vcwin > Vision & Control vcwin

. Terminate vcwin with ALT+F4 or

with the menu item

File > Exit

Choose the interface in vcwin

After having started vcwin, you should choose the port to which the vision

system is connected by calling

Communication > Interface

from the menu.

Connecting the device with vcwin

Connect the device by calling

Communication > Connect

999.994.347.10-en-2.7

Summary of Contents for vicosys 5300





























































Search results

Summary of Contents for vicosys 5300

Reviews:

Brands by name

Popular brands

Vision & Control vicosys 5300, Instructions For Use Manual

Search results

Summary of Contents for vicosys 5300

Reviews:

Brands by name

Popular brands