Viola Systems Arctic Substation Gateway User Manual Download

Page: 42 / 51

User Manual
Arctic Substation Gateway

Firmware Version 2.4.x

Document Version 1

IEC-101 slave link address

Units

N/A

Value range

1-65000

Note

The link-level address of IEC-101 slave.

Link address field length
Defines the length of the IEC-101 link-level address field in bytes.

Table 39: IEC-101 slave link address field length

IEC-101 slave link address field length

Type

Field length

Units

Bytes

Value range

1, 2

Note

The link-level address of IEC-101 slave.

Event poll interval
It defines the IEC-101 event polling interval in 0.1 second increments (class 1
or 2 poll).

Table 40: IEC-101 event poll interval

IEC-101 event poll interval

Type

Interval

Units

0.1 seconds

Value range

1-65000

Note

The events are polled only when the
IEC-104 connection is active.

Link test interval
It defines the IEC-101 link test interval in 0.1 second increments. Link test is
performed if there is no other activity.

Table 41: IEC-101 link test interval

IEC-101 link test interval

Type

Interval

Units

0.1 seconds

Value range

1-65000

Note

The link test is performed if there is no
other activity during defined interval.

Keep link open
Defines that the IEC-101 link is kept always open even when there is no active
IEC-104 connection. If the functionality is enabled the Arctic sends link test

Summary of Contents for Arctic Substation Gateway




















































Search results

Summary of Contents for Arctic Substation Gateway

Reviews:

Related manuals for Arctic Substation Gateway

Brands by name

Popular brands

Viola Systems Arctic Substation Gateway, User Manual

Search results

Summary of Contents for Arctic Substation Gateway

Reviews:

Related manuals for Arctic Substation Gateway

Brands by name

Popular brands