Viola Systems Arctic Substation Gateway User Manual Download Page 47

Page: 47 / 51

User Manual
Arctic Substation Gateway

Firmware Version 2.4.x

Document Version 1

Maximum collected time

Value range

1-255

Note

The value must be smaller than t1.

Max packets

Max packets are defined as the maximum amount of IEC-101 packets stored
into the packet collector before sending the data to the network.

Table 54: Maximum collected packets

Maximum collected packets

Type

Packet count

Units

Packets

Value range

1-255

Note

7.8

Other settings

Write syslog

It defines whether the error messages are stored to system log file or not.

Table 55: Write system log

Write system log

Type

Boolean

Units

N/A

Value range

No, Yes

Note

The system log is available by using WEB UI.

Summary of Contents for Arctic Substation Gateway




















































Search results

Summary of Contents for Arctic Substation Gateway

Reviews:

Related manuals for Arctic Substation Gateway

Brands by name

Popular brands

Viola Systems Arctic Substation Gateway, User Manual

Search results

Summary of Contents for Arctic Substation Gateway

Reviews:

Related manuals for Arctic Substation Gateway

Brands by name

Popular brands