background image

V20BVCBK

5

User Manual

The room for installing the appliance must be at least 1 cubic metre per 8 grams of

refrigerant. The refrigerant quantity contained in this appliance is listed above in

grams; it is also noted on the Rating Plate of the appliance.

It is hazardous for anyone other than an Authorised Service Person to carry out

servicing or repairs to this appliance.

– WARNING: Keep ventilation openings in the appliance enclosure or in the built-in

structure clear of obstruction.

– WARNING: Do not use mechanical devices or other means to accelerate the defrosting

process, other than those recommended by the manufacturer.

– WARNING: Do not damage the refrigerant circuit.

– WARNING: Do not use electrical appliances inside compartments of the appliance.

– WARNING: In Queensland Australia the authorized person must hold a Gas Work

Authorisation for hydrocarbon refrigerants, before carrying out servicing or repairs which

involve the removal of covers.

The environment and personal safety must be considered when disposing of this appliance.

Please ensure the appliance is taken to a recycle center for safe recycling. DO NOT

dispose of the appliance in land fill as the insulation and refrigerant gas contained in these

appliances are flammable.

Allow 24 hours before switching on the Beverage Center. During this time we

recommend that you leave the door open to clear any residual odors.

BEFORE LOADING & PLUGGING IN THE BEVERAGE CENTER

Important: All models without front venting (air opening) are strictly for free standing

only. ( see technical chart)

Recommendations:

The location you have selected for your Beverage Center should:

- be unencumbered and well ventilated;

- be well away from any heat source and direct sunlight;

- not be too damp (laundry, pantry, bathroom etc.);

- have a flat floor;

- have a standard and reliable electricity supply (standard socket to country standards,

linked to the ground), it is NOT recommended to use a multi-socket or extension lead.

- have a surge protector fitted to the electrical outlet;

- away from the microwave oven. Certain microwave ovens do not have wave interference

shield. When placed within 1 meter vicinity of the Beverage Center, they may affect the

operation of the Beverage Center.

Summary of Contents for AL-V40BVC





















Reviews: