background image

                                                       

 

                       

 

- 6 - 

Temperature and Humidity 

 

1.  The controller 

 

Fig. 2 TEMPERATURE CONTROLLER 

1) Keys 

 

SET: 

To  display  set-point;  in  programming  mode  it  selects  a  parameter  or 

confirms an operation. 

To start a manual defrost. 

To see the maximum stored temperature; in programming mode it browses 

the parameter codes or increases the displayed value. 

 : 

To see the minimum stored temperature; in programming mode it browses 

the parameter codes or decreases the displayed value. 

To turn on/off the power to the unit.

 

+

To lock/unlock the keypad. 

SET+

To enter in the programming mode.

 

SET+

To return to the

 

temperature display.

  

 

2) Lock and unlock the keys 

 

To lock the keys, press up + down keys 

+  until POF is displayed; to unlock 

the keys, press up + down keys 

+  until PON is displayed.

 

 

3) Display 

 
During  normal  operating  conditions,  the  display  shows  the  value  measured  by 
the  air  temperature  probe.  In  case  of  active  alarm,  the  temperature  flashes 
alternately to the code alarm. The LED functions are listed as follows. 
 

LED 

MODE 

FUNCTION 

 

ON 

Compressor enabled  

 

Flashing

 

Anti-short cycle enabled 

 

ON 

Defrost enabled 

 

ON 

Fan enabled 

 

Flashing 

Fan delay after defrost enabled 

 

ON 

Alarm occurring 

 

ON 

Temperature measuring unit 

 

Flashing 

Programming mode 

Summary of Contents for WINE-MATE WM-2500SSR
































Reviews: