background image

                                                       

 

                       

 

- 23 - 

 

 

Fig. 13 Condenser Fan Cycle Control 

 
2)  A  fan  speed  control  may  be  used  to  adjust  the  air  flow  to  achieve  the 

specified CFM. The fan will run from the minimum speed to full speed with the 
control knob at the lowest and highest speed position. To adjust the minimum 
speed, turn control knob to the lowest speed position, then rotate the setting 
(located  on  the  side  or  front)  clockwise  to  decrease  the  minimum  speed  or 
counter-clockwise  to  increase  the  minimum  speed.  The  minimum  speed 
should be adjusted until it supplies the required CFM. 
 

 

 

Fig. 14 Fan Speed Control 

 

3)  The subcooling at the condensing unit shall be around 10°F. The charge may 

be complete when there are no more bubbles forming in the liquid indicator. 

4)  The  head  pressure  shall  be  120  ~  150  psig  at  70  ~  90  °F  condensing  unit 

operating temperatures. 

5)  The  evaporator’s  constant  pressure  expansion  valve  is  set  around  30  ~  35 

psig  (35  ~  40°F)  at  factory.  This  pressure  setting  gives  a  dew  point  to 
maintain the proper humidity for storing wine. 

6)  The temperature split across the evaporator shall be 8 ~ 10°F at 55°F wine 

cellar temperature. 

7)  Again, you must verify if the superheat at the evaporator unit is 9 ~ 18°F at 

55 °F ~ 65 °F wine cellar temperatures. 

Summary of Contents for WINE-MATE WM-2500SSR
































Reviews: