vinmetrica SC-100A User Manual Download Page 7

SC-100A manual 

Version 3.1c 

WARRANTIES AND LIABILITIES 

1.  

The materials provided in the kit, as described on pages 1 and 2 above, (“Materials”) are 
warranted as follows: The SC-100A instrument, electrode and non-reagent accessories are 
warranted against defects in workmanship for 24 months from date of purchase.  The reagents 
are warranted to perform as described herein up until any stated expiration date or 6 months 
after purchase, whichever is later.  THE WARRANTIES IN THESE TERMS AND 
CONDITIONS ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY, 
NONINFRINGEMENT, OR FITNESS FOR A PARTICULAR PURPOSE, SAID 
WARRANTIES BEING EXPRESSLY DISCLAIMED. 

 
2.   

Buyer agrees that its sole and exclusive remedy against Vinmetrica shall be limited to the repair 
and replacement of Materials or parts of Materials, provided Vinmetrica is promptly notified in 
writing, prior to the expiration of the warranty period specified above, of any 
defect.  Vinmetrica’s liability for any damages due Buyer shall be limited to the purchase price 
of the Materials.  

 
3.    

VINMETRICA'S MAXIMUM LIABILITY FOR ALL DIRECT DAMAGES, INCLUDING 
WITHOUT LIMITATION CONTRACT DAMAGES AND DAMAGES FOR INJURIES TO 
PERSONS OR PROPERTY, WHETHER ARISING FROM VINMETRICA’S BREACH OF 
THESE TERMS AND CONDITIONS, BREACH OF WARRANTY, NEGLIGENCE, STRICT 
LIABILITY, OR OTHER TORT WITH RESPECT TO THE MATERIALS, OR ANY 
SERVICES IN CONNECTION WITH THE MATERIALS, IS LIMITED TO AN AMOUNT 
NOT TO EXCEED THE PRICE OF THE MATERIALS.  IN NO EVENT SHALL 
VINMETRICA BE LIABLE TO BUYER FOR ANY INCIDENTAL, CONSEQUENTIAL OR 
SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOST REVENUES AND 
PROFITS.  

 

 
HAZARDS AND TOXICITY 
 

 

All Materials offered by Vinmetrica are intended for use by individuals who are familiar with 

laboratory procedures and their potential hazards.  The Materials contain chemicals which may be 
harmful if misused.  Due care should be exercised with all Materials to prevent direct human contact. 
Glassware can break and chemicals can splash during experiments; 

Always

 

use safety glasses

. We 

strongly recommend using nitrile or latex gloves and wearing long pants, long sleeves and closed toed 
shoes.  Keep out of reach of children. 

 
 
 

 

6084 Corte Del Cedro Suite 105, Carlsbad CA 92011 

www.vinmetrica.com

 

(760) 494-0597 

[email protected]

 

  

Copyright 2010-20. Sportsman Consulting, LLC DBA Vinmetrica.  All rights reserved. 

Summary of Contents for SC-100A













Reviews: