Vingtor A-100 Installation & User Manual Download Page 26

Page: 26 / 115

Installation & User Manual

System CTB-100V

4.1.7 Receive a call from two or more substations.

Calls can be received from two or more substations at same time. The operation panel that is set to receive calls
can select between calls from substations.
Calls are indicated with flashing green

LED

in the push buttons and a beep tone in the monitor loudspeaker

Will also activate extra signal unit if installed. (Only for the first incoming call.)
.

•

Calls are indicated with flashing green

LED

for respective line button,

and signal in monitor loudspeaker.
(And in extra signal unit if installed, Note! only for the first call)

•

Press the

LINE

button, the call is set up. Indicated by steady green LED

The the operation panel can select between substation lines and cancel
calls by pressing the respective LINE button once more.

Operationpanel with gooseneck microphone MB-30G

•

Press the

TALK

button.

Speak clearly into the microphone. When the

TALK

button is released

the operation panel will be in listening mode, and you will hear the
communication from the selected station.

PTT SWITCH

ETC-1-TB

Operationpanel with hand microphone ETC-1-TB

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operation panel will be in listening mode, and you will hear
the communication from the selected station.

PTT SWITCH

Operationpanel with hand microphone P-66

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operation panel will be in listening mode, and you will hear
the communication from the selected station.

•

Press the selected

LINE

buttons once more to end the call.

The LED`s will be switch off.

Summary of Contents for A-100




















































































































Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands

Vingtor A-100, Installation & User Manual

Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands