Vingtor A-100 Installation & User Manual Download Page 22

Page: 22 / 115

Installation & User Manual

System CTB-100V

4.1.2 Make a call to group of substations.

You can select group of substations by pressing respective line buttons from one of the four
Operation panels. Only the operation panels can switch off and end the call

•

Press the required

LINE

buttons, the call is set up. Indicated by steady

green LED in selected buttons.

•

Press the

SIGN

button

A tone signal will be given to selected station as long as the

SIGN

button is kept pressed.
This will also activate extra signal devices, if connected (Se pos.4.1.5)

Operation panel with gooseneck microphone MB-30G

•

Press the

TALK

button.

Speak clearly into the microphone. When the

TALK

button is released

the operation panel will be in listening mode, and you will hear the
communication from the selected stations.

PTT SWITCH

ETC-1-TB

Operation panel with hand microphone ETC-1-TB

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operation panel will be in listening mode, and you will hear
the communication from the selected station.

PTT SWITCH

Operation panel with hand microphone P-66

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operation panel will be in listening mode, and you will hear
the communication from the selected stations.

•

Press all the

LINE

buttons once more to end the call.

The LED will be switch off.

Summary of Contents for A-100




















































































































Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands

Vingtor A-100, Installation & User Manual

Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands