Vingtor A-100 Installation & User Manual Download Page 25

Page: 25 / 115

Installation & User Manual

System CTB-100V

4.1.6 Receive a call from an substation.

A call are indicated with flashing green

LED

in the push button and a beep tone in the monitor loudspeaker or

extern loudspeaker. Will also activate extra signal unit if installed. Only the operationpanel can switch off and end
the call.

•

A call is indicated with flashing green

LED

in for respective line button,

and signal in the monitor loudspeaker.
(and in extra signal unit if installed.)

•

Press the

LINE

button, the call is set up. Indicated by steady green LED

Operationpanel with gooseneck microphone MB-30G

•

Press the

TALK

button.

Speak clearly into the microphone. When the

TALK

button is released

the operationpanel will be in listening mode, and you will hear the
communication from the selected station.

PTT SWITCH

ETC-1-TB

Operationpanel with hand microphone ETC-1-TB

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operationpanel will be in listening mode, and you will hear
the communication from the selected station.

PTT SWITCH

Operationpanel with hand microphone P-66

•

Press the

PTT SWITCH

Speak clearly into the microphone. When the

PTT SWITCH

button is

released the operationpanel will be in listening mode, and you will hear
the communication from the selected station.

•

Press

LINE

button once more to end the call.

The LED will be switch off.

Summary of Contents for A-100




















































































































Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands

Vingtor A-100, Installation & User Manual

Search results

Summary of Contents for A-100

Reviews:

Related manuals for A-100

Brands by name

Popular brands