manualshive.com logo in svg

Viking Electronics 40TB-IP, Product Manual, Page: 16 / 20

Share
Download
Viking Electronics 40TB-IP Product Manual Download Page 16

16

36.  Import/Export

The Import/Export feature is useful for backing up all the 

40TB-IP’s

programming or for importing programming when

installing multiple units with a majority of the same programming.

Clicking on the “Clear Speaker Settings” button in programming will reset all of the Programming Features back to their
factory default settings. 

Note: 

This    command will not change or reset your IP settings.

37  Clear Speaker Settings 

Clicking on the “Clear IP Settings” will reset all of the IP SETTINGS back to their factory default settings. 

Note: 

This

will not effect any speaker or paging settings..

37  Clear IP Settings 

38.  Diagnostics

The Diagnostics section in the Viking IP Programming can be used to test the functionality of the mic, speaker and
relay.

35.  Phone Firmware

If new 

40TB-IP

firmware is available, after opening the programming software a pop up window will ask if you would

like to update firmware. Another way to update is accomplished by clicking the phone firmware “Update” button. You
can then browse to the folder that contains the HEX file for updating the unit’s firmware. This method is typically only
used when Viking Technical Support has sent you updated firmware.

Summary of Contents for 40TB-IP





















Reviews:

No comments