manualshive.com logo in svg

Viglen vig830s, User Manual, Page: 24 / 77

Share
Download
Viglen vig830s User Manual Download Page 24

V1.0                                   Vig830S Motherboard Manual 

23 

 

Front panel audio connector (10-1 pin AAFP) 

This  connector  allows  you  to  connect  the  front  panel  audio  and  is  compliant  with  Intel®  Front  Panel  I/O 
Connectivity Design Guide

. 

 

 

 

Figure 14: 

Front panel audio connector 

 
 
 
 

 

Chassis intrusion connector (4-1 pin CHASSIS) 

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the 
chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a 
high-level signal to this connector when a chassis component is removed or replaced. The signal is then 
generated as a chassis intrusion event.  By default, the pin labeled “Chassis Signal” and “Ground” are 
shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion 
detection feature.

 

 

 

 

Figure 15:

 Chassis intrusion connector

 

 
 
 
 

Summary of Contents for vig830s














































































Reviews:

No comments