manualshive.com logo in svg

Viglen vig830s, User Manual, Page: 12 / 77

Share
Download
Viglen vig830s User Manual Download Page 12

V1.0                                   Vig830S Motherboard Manual 

11 

• LAN wake capabilities  
• LAN subsystem software 
 

RJ-45 LAN Connector LEDs 

The two LEDs are built into the RJ-45 LAN connector located on the back panel. These 
LEDs indicate the status of the LAN as shown in Table 1. 

  

 

 

 

Figure 5:

 LAN Connector LED Locations 

Table 2:

 LAN LED Status 

 

 

 
 
Universal Serial Bus (USB) 

 

 
The motherboard supports up to 7 USB 2.0 ports and 3 USB 3.0. The port arrangement 
is a follows: 
 

  Two USB 2.0 ports are implemented with stacked back panel connectors (black) 

  Six USB 3.0 ports are implemented with stacked back panel connectors (blue) 

  One USB 2.0 front panel ports are implemented through three dual-port internal 

headers 

  Two USB 3.0 front panel ports are implemented through one dual-port internal header 

 
All USB ports are high-speed, full-speed, and low-speed capable. 
 

NOTE:

 

Computer  systems  that  have  an  unshielded  cable  attached  to  a  USB  port  may 

not  meet  FCC  Class B  requirements,  even  if  no  device  or  a  low-speed  (sub-channel) 
USB device is attached to the cable.  Use shielded cable that meets the requirements for 
high-speed (fully rated) devices.  

 

 
 
 

Summary of Contents for vig830s














































































Reviews:

No comments