manualshive.com logo in svg

Viglen vig830s, User Manual, Page: 10 / 77

Share
Download
Viglen vig830s User Manual Download Page 10

V1.0                                   Vig830S Motherboard Manual 

9 

Graphics Subsystem 

 
The board supports system graphics through either Intel Graphics Technology or a 
PCI Express x16 add-in graphics card. 
 

Integrated Graphics

 

 
The board supports integrated graphics through the Intel® Flexible Display Interface 
(Intel® FDI) for processors with Intel Graphics Technology. 
 

Analog Display (VGA) 
 

The VGA port supports analog displays. The maximum supported resolution is 1920 x 
1200 at 60Hz refresh rate. The VGA port is enabled for POST whenever a monitor is 
attached, regardless of the DVI-D connector status. 
 

DVI-D 

The maximum supported resolution is 1920 x 1200 at 60Hz 

 
DisplayPort  

The maximum supported resolution is 4096 x 2304 @60Hzat 60Hz refresh rate. 

 
HDMI 

The maximum supported resolution is 4096 x 2304 at 24Hz/ 2560 x 1600 at 60Hz 
 

Multiple Display Configurations 

The following multiple display configuration modes are supported (with appropriate driver 
software):  
 
•  Single Display is a mode with one display port activated to display the output to one 

display device.  

 
•  Intel® Display Clone is a mode with up to three display ports activated to drive the 

display content of same color depth setting but potentially different refresh rate and 
resolution settings to all the active display devices connected.  

 
•  Extended Desktop is a mode with up to three display ports activated to drive the 

content with potentially different color depth, refresh rate, and resolution settings on 
each of the active display devices connected. 

 

PCI Express 3.0/2.0 x16 (1@x4) slots 

The Intel Core i7/i5/i3, Pentium and Celeron processors in the LGA1150 socket support 
discrete add in graphics cards through the PCI Express 2.0 x16 connector: 
 

  Supports PCI Express GEN3 frequency of 2.5 GHz resulting in 8.0 Gb/s each 

direction (1000 MB/s) per lane. Maximum theoretical bandwidth on interface is 
16GB/s in each direction, simultaneously, when operating in x16 mode. 

 

  Supports PCI Express GEN2 frequency of 2.5 GHz resulting in 5.0 Gb/s each 

direction (500 MB/s) per lane. Maximum theoretical bandwidth on interface is 8GB/s 
in each direction, simultaneously, when operating in x16 mode. 

 

Summary of Contents for vig830s














































































Reviews:

No comments