Viessmann Vitotronic 100 GC1 Installation And Service Instructions Manual Download

Page: 63 / 132

Installation

Connection of External Controls (VD2/VD2A only)

(continued)

Modulating boilers – operation with external modulation controller

Settings on the control unit

The settings for the fixed high limit and
the other settings are dependent on the
safety equipment installed in
accordance with applicable codes.

Non-condensing boiler
(VD2/VD2A)

C /

Condensing boiler
(CT3)

C /

Condensing boiler
(CM2)

C /

Fixed high limit

110 / 230

99 / 210

Adjustable high limit

100 / 212

95 / 203

Coding for the electronic maximum
temperature limiter of Vitotronic 100;
set code 06 to the temperature as
shown or less

93 / 200

87 / 188

88 / 190

Single-boiler systems:

Coding ”01: 1”
(factory setting)

When a building automation system is
connected, only the connections on
plug

aVD

are required. The DHW tank

control unit is activated when the DHW
tank temperature sensor is connected.
The boiler water temperature must be
set to the minimum value.

Multi-boiler systems:

Set coding ”01: 3”

When a building automation system
is connected, the connections on
plugs

aVD

and

aVH

are required. The

DHW tank temperature and the
load-dependent cascade control
must be controlled through the
external building automation system.

The boiler activation contact is
essential on multi-boiler systems.
The contact on the lead boiler must
be constantly closed.

CAUTION

Summary of Contents for Vitotronic 100 GC1





































































































































Search results

Summary of Contents for Vitotronic 100 GC1

Reviews:

Related manuals for Vitotronic 100 GC1

Brands by name

Popular brands

Viessmann Vitotronic 100 GC1, Installation And Service Instructions Manual

Search results

Summary of Contents for Vitotronic 100 GC1

Reviews:

Related manuals for Vitotronic 100 GC1

Brands by name

Popular brands