Viessmann VITODENS 200-W B2HA 112 Page 58 Service Instructions Manual Download

Page: 58 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Coding 2

Solar

Select “Solar”

Note:

The solar group is only displayed if a solar control module, type SM1, is connected.

Coding
Coding in the factory setting

Possible change

00:8

The solar circuit pump starts

when the collector temperature

exceeds the actual DHW tank

temperature by 8 K.

00:2

00:30

The differential between

the actual DHW tank temperature

and the start point for the solar

circuit pump can be adjusted from

2 to 30 K.

01:4

The solar circuit pump is switched

off when the differential between

the collector temperature and the

actual DHW tank temperature is

less than 4 K.

01:1

01:29

The differential between the

actual DHW tank temperature and

the stop point for the solar circuit

pump can be adjusted from 1 to

29 K.

02:0

Solar circuit pump (stepped)

is not speed-controlled

02:1

Solar circuit pump is speed-

controlled with wave packet

control.

02:2

Solar circuit pump is speed-

controlled with PWM control.

03:10

The temperature differential

between the collector

temperature and actual DHW

tank temperature is regulated

to 10 K.

03:5

03:20

The differential temperature

control between collector

temperature and actual DHW tank

temperature can be adjusted from

5 to 20 K.

04:4

Controller amplification of the

speed control 4%/K.

04:1

04:10

Controller amplification adjustable

from 1 to 10%/K.

05:10

Minimum speed of the solar

circuit pump 10% of the

maximum speed.

05:2

05:100

Minimum speed of the solar

circuit pump is adjustable from

2 to 100%.

06:75

Maximum speed of the solar

circuit pump 75% of the

maximum possible speed.

06:1

06:100

Maximum speed of the solar

circuit pump is adjustable from 1

to 100%.

07:0

Interval function of the solar

circuit pump switched off.

07:1

Interval function of the solar

circuit pump switched on. To

capture the collector temperature

more accurately, the solar circuit

pump starts for short cycles.

08:60

The solar circuit pump is

switched off when the

actual DHW tank temperature

reaches 140°F (60°C)

(maximum DHW tank

temperature).

08:10

08:90

The maximum DHW tank

temperature can be adjusted

from 50 to 194°F (10 to 90°C).

Summary of Contents for VITODENS 200-W B2HA 112









































































































Search results

Summary of Contents for VITODENS 200-W B2HA 112

Reviews:

Related manuals for VITODENS 200-W B2HA 112

Brands by name

Popular brands

Viessmann VITODENS 200-W B2HA 112, Service Instructions Manual

Search results

Summary of Contents for VITODENS 200-W B2HA 112

Reviews:

Related manuals for VITODENS 200-W B2HA 112

Brands by name

Popular brands