manualshive.com logo in svg

Viessmann VITODENS 200-W B2HA 112, Service Instructions Manual, Page: 54 / 104

Share
Download
Viessmann VITODENS 200-W B2HA 112 Service Instructions Manual Download Page 54

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

54

Coding 2

General 

(continued)

Coding in the factory setting

Possible change

8A:175

DO NOT ADJUST

--

--

--

8F:0

Operation in the standard

menu and extended

menu enabled

Note: 

The respective code is

         only activated when you

         exit the service menu

8F:1

Operation in the standard

menu and extended menu

blocked.

Emissions test mode can

be enabled

8F:2

Operation enabled in the

standard menu; blocked in

the extended menu.

Emissions test mode can

be enabled

90:128

Time constant for calculating 

the adjusted outside 

temperature 21.3 h

90:1

to

90:199

Fast (low values) or slow (high 

values) matching of the flow 

temperature, subject to the set

value when the outside 

temperature changes;

1 step 

≙

 10 minutes.

93:0

0-5000 ft.

93:1 - 93:5

NOT USED

93:6

5000-10000 ft.

94:0

Without Open Therm extension

94:1

With Open Therm extension 

(automatic recognition).

95:0

Without Vitocom 100 

communication interface

95:1

With Vitocom 100 communication 

interface (automatic recognition).

97:0

With LON communication 

module: The outside 

temperature of the sensor 

connected to the control unit is 

utilized internally

97:1

Control unit receives outside 

temperature.

97:2

Control unit transmits the outside 

temperature to the Vitotronic 

200-H.

98:1

Viessmann system number

(in conjunction with monitoring 

several systems via Vitocom 

300)

98:1

to

98:5

System number adjustable from 

1 to 5.

99:0

DO NOT ADJUST

--

--

9A:0

DO NOT ADJUST

--

--

9B:70

Set flow temperature for 

external demand 158°F (70°C)

9B:0

to

9B:127

Set flow temperature for external 

demand adjustable from 32 to 

260°F (0 to 127°C) (limited by 

boiler-specific parameters).

9C:20

Monitoring LON participants.

If a participant fails to respond, 

the values specified inside the 

control unit will be used after

20 minutes. Only then will a 

fault message be issued. 

9C:0

No monitoring

9C:5

to

9C:60

Time adjustable from 5 to 60 

minutes.

9F:8

Differential temperature 8 K; 

only in conjunction with mixing 

valve circuit

9F:0

to

9F:40

Differential temperature adjustable 

from 0 to 40 K.

Summary of Contents for VITODENS 200-W B2HA 112









































































































Reviews:

No comments