Viessmann VITODENS 200-W B2HA 112 Service Instructions Manual Download Page 74

Page: 74 / 104

Vitodens 200-W B2HA 112, 150 Service

5683 710 - 09

Fault Codes

(continued)

Troubleshooting

Control mode: Boiler/burner fully operational (fault code must be verified and reset).

Burner in fault mode: Boiler control requires manual reset before burner can resume operation.

Burner blocked: If fault cause is corrected, burner resumes operation.

Detailed fault code coding address 38:xx (if available).

Fault code

on display

Detailed fault

code

System behavior

Cause

Corrective action

No solar DHW heating

Tank temperature

sensor

cable broken

Check temperature sensor

on solar control module.

Control mode

No flow rate in collector

circuit or flow rate too

low or temperature

limiter has responded

Check solar circuit

pump and solar circuit.

Acknowledge fault message.

Control mode

Solar control module

faulty

Replace solar control module.

Burner blocked

Flue gas temperature

sensor not properly

positioned

Properly install flue gas

temperature sensor.

DO NOT

USE

Control mode

Max. system pressure

exceeded

Check system pressure (max.

system pressure 3 bar).

Check the function and sizing

of the diaphragm expansion

vessel. Vent the heating system

Control mode (stays in

factory default setting)

Faulty programming

unit

Replace the programming unit.

141

Burner blocked

Flue gas temperature

sensor shorted out

Check flue gas temperature

sensor (see page 81).

Control mode (stays in

factory default setting)

Communication fault;

programming unit

(internal)

Check connections and

replace programming unit

if required.

Control mode

(factory default setting)

Internal fault

Replace the control unit.

Burner blocked

Boiler coding card

missing, faulty or

incorrect boiler coding

card

Plug in boiler coding card or

replace if faulty.

141

Burner blocked

Flue gas temperature

sensor cable broken

Check flue gas temperature

sensor (see page 81).

Mixing valve regulates to

a flow temperature of

68°F (20°C)

Communication fault -

accessory kit for

heating circuit 2 with

mixing valve

Check extension kit connections

and code.

Mixing valve regulates to

a flow temperature of

68°F (20°C)

Communication error,

extension kit for heating

circuit 3 (with mixing

valve)

Check extension kit connections

and code.

Control mode without

remote control

Communication error,

remote control Vitotrol

heating circuit 1

(without mixing valve)

Check connections, cable,

coding address “A0” in “Heating

circuit” group and remote

control unit setting.

Summary of Contents for VITODENS 200-W B2HA 112









































































































Search results

Summary of Contents for VITODENS 200-W B2HA 112

Reviews:

Viessmann VITODENS 200-W B2HA 112, Service Instructions Manual, Page: 74 / 104

Search results

Summary of Contents for VITODENS 200-W B2HA 112

Reviews: