Viessmann B2HB 45 Installation Instructions Manual Download Page 18

Page: 18 / 60

Vitodens 200-W B2HB 45, 57 Installation

5680 493 - 05

Connections

Boiler Connections

Boiler venting

The Vitodens 200-W B2HB boiler comes with a pre-installed

vent pipe adaptor.

Run venting system, single-wall or coaxial, through the

side wall or the roof, taking the shortest possible route

and at a rising angle (min. 3º).

Proper piping practice

Support piping by proper suspension method. Piping

must not rest on or be supported by boiler. Use moderate

amount of dope.

Gas shut-off valve connection

1. Make gas connections in accordance with codes

CAN/CSA B149.1 and .2 or National Fuel Gas Code

ANSI Z223.1/NFPA 54, as well as local codes.

2. Connect gas shutoff valve to the boiler gas

connection.

3. Once connected close gas shutoff valve on boiler.

Connecting power

The Vitodens 200-W boiler has a external accessories

connection box installed, which requires a 120VAC/12A

power supply. Refer to the wiring diagram (see page 44).

WARNING

Remove outer gasket if single wall (boiler room air

dependant) venting system is used.

See following page for details on gas

connection and piping.

Manual gas shutoff

Closed

Open

2 imperfect threads

Leave 2 threads bare

Summary of Contents for B2HB 45





























































Search results

Summary of Contents for B2HB 45

Reviews:

Related manuals for B2HB 45

Brands by name

Popular brands

Viessmann B2HB 45, Installation Instructions Manual

Search results

Summary of Contents for B2HB 45

Reviews:

Related manuals for B2HB 45

Brands by name

Popular brands