Vetus M4.15 SOLAS Operation Manual Download

Page: 7 / 80

Safety measures

Introduction

All safety instructions in this manual are desig-
nated by the accompanying symbol. Please follow
them carefully.

Pass the safety instructions to other persons operating the
engine as well.

General regulations and laws for safety and accident prevention
must also be observed.

• Never attempt to touch moving parts when the engine is run-

ning.

• Never touch hot parts of the engine, and keep flammable

materials well away from the engine.

• Always stop the engine before checking or adjusting compo-

nents.

• Always stop the engine before checking or topping up the

coolant or oil.

• N

ever

open cap on top of header tank when the engine is at

operating temperature.

• Always carry out maintenance safely by only using tools well

matched in size.

Summary of Contents for M4.15 SOLAS

















































































Search results

Summary of Contents for M4.15 SOLAS

Reviews:

Related manuals for M4.15 SOLAS

Brands by name

Popular brands

Vetus M4.15 SOLAS, Operation Manual

Search results

Summary of Contents for M4.15 SOLAS

Reviews:

Related manuals for M4.15 SOLAS

Brands by name

Popular brands