Vetus M4.15 SOLAS Operation Manual Download

Page: 18 / 80

After repair work:

Check that all guards have been replaced
and that all tools have been removed from
the engine.
When starting with pre-heating, do not use
any other substance (e.g. injection with
‘Easy Start’). Doing so could result in an
accident.

Preparation starting

Before starting the engine, always check
that the control lever(s) is (are) in the neu-
tral position.

Never start the engine with
the fuel injection pump
removed.
Disconnect battery.

Set the control lever to ‘half throttle’

with-

out

engaging the gearbox.

Use

Starting

Before starting,

alWays

check the follow-

ing points:

•  Engine oil level.
•  Coolant level.
•  Sea cock open.
•  Main switch ‘

’.

• Gearbox in ‘

Neutral

’ position.

neutral

gearbox

forward

half throttle,
gearbox

not

engaged

gearbox
reverse

reverse

throttle

forward

throttle

VD00111

VD00112

Summary of Contents for M4.15 SOLAS

















































































Search results

Summary of Contents for M4.15 SOLAS

Reviews:

Related manuals for M4.15 SOLAS

Brands by name

Popular brands

Vetus M4.15 SOLAS, Operation Manual

Search results

Summary of Contents for M4.15 SOLAS

Reviews:

Related manuals for M4.15 SOLAS

Brands by name

Popular brands