VESPA GTS Super 125 i.e. Service Station Manual Download Page 243

Page: 243 / 285

- Abnormal noise

Static test

Static control after the test ride:

• Hot engine restart

• Minimum seal (turning the handlebar)

• Uniform steering rotation

• Possible losses

• electric radiator fan operation

CAUTION

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE.

CAUTION

NEVER EXCEED THE RECOMMENDED INFLATION PRESSURES OR TYRES MAY BURST.

Functional inspection

Functional Checks:

• Hydraulic braking system: lever travel

• Clutch: proper functioning check

• Engine: proper general functioning and no abnormal noise check

• Other: papers check, chassis and engine number check, tools and equipment, licence plate fitting,

lock check, tyre pressure check, rear-view mirror and any accessory fitting

Vespa GTS Super 125 i.e.

Pre-delivery

PRE DE - 243

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands