VESPA GTS Super 125 i.e. Service Station Manual Download Page 163

Page: 163 / 285

With wiring disconnected from the control unit and connected to the system, check that the sensor

resistance between pins 20 - 29 is between 100 and 150 Ohm at an engine temperature of approxi-

mately 20°

Disconnect the fuel pipe connector. Start up the engine and wait for it to stop. With the wiring connected

to the control unit and system try to start-up the engine and check that the voltage between pins 20 and

29 is around 2.8 V

With the interface wiring disconnected from the control unit, check continuity between pin 29 and the

red cable of the engine speed sensor connector and between pin 20 and the brown cable of the engine

speed sensor connector

With the interface wiring disconnected from the control unit and engine speed sensor connector , check

that the Red and Brown cables (pin 29 - 20) are isolated from each other and insulated from the ground.

Specific tooling

020481Y

Control unit interface wiring

020331Y

Digital multimeter

Vespa GTS Super 125 i.e.

Injection

INJEC - 163

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands