VESPA GTS Super 125 i.e. Service Station Manual Download Page 219

Page: 219 / 285

- Screw the two pad lock pins to the correct torque, and apply the recommended product.

- Fit the calliper on its support, tightening the two screws to the prescribed torque.

N.B.

IF IT IS NOT POSSIBLE TO CORRECTLY POSITION THE CALLIPER ON THE DISC DURING FIT-
TING, GENTLY EXPAND THE PADS.

Recommended products

Loctite 243

Medium strength threadlock

Medium Loctite 243 threadlock

Locking torques (N*m)

Screw tightening calliper to support

24 to 27

Pad fastening pin

19.6 to 24.5

Rear brake pads

Removal

- Remove the rear brake calliper.

- Remove the snap ring, slide off the pad retention

pin and the clip.

- Remove the brake pads and check there are no

faults or warping. Otherwise, replace them.

- Check the thickness of the friction material is

more than 1.5 mm. If it is not, replace it

- The replacement must be made with greater re-

sidual thickness if the pad has not worn evenly. A

0.5 mm thickness difference in the residual friction

material is permitted

Vespa GTS Super 125 i.e.

Braking system

BRAK SYS - 219

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands