VESPA GTS Super 125 i.e. Service Station Manual Download Page 199

Page: 199 / 285

Overhaul

- The bracket for the shock absorber -calliper at-

tachment has two roller bearings separated one

from the other as shown in the photograph

- Remove the two roller bearings from the bracket

with the specific tool operating on the shock ab-

sorber attachment side as shown in the photo-

graph

Specific tooling

020376Y

Adaptor handle

020441Y

26 x 28 mm adaptor

020365Y

22 mm guide

- Remove the oil seal on the wheel hub side with

the screwdriver as shown in the photograph

- Suitably hold the brake calliper - shock absorber

attachment bracket

- Fit a new oil seal and move it until it stops using

the specific tool

Specific tooling

020376Y

Adaptor handle

020360Y

52 x 55-mm Adaptor

Vespa GTS Super 125 i.e.

Suspensions

SUSP - 199

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Brands by name

Popular brands