manualshive.com logo in svg

VESPA GTS Super 125 i.e., Service Station Manual

Share
Download
VESPA GTS Super 125 i.e. Service Station Manual Download Page 200

- Assemble a new roller bearing on the shock ab-

sorber side and move it until it stops using the

specific tool

Specific tooling

020036Y

 

Punch

- Suitably hold the brake calliper - shock absorber

attachment bracket

- Assemble a new roller bearing on the wheel hub

side and move it until it stops using the specific tool

Specific tooling

020037Y

 

Punch

Refitting

- Refit the parts in reverse order of the removal

operation.

CAUTION

BEFORE CARRYING OUT REFITTING OPERATIONS IN
THE AREAS MARKED WITH AN ASTERISK, LUBRICATE
THEM WITH THE RECOMMENDED PRODUCT

Specific tooling

020036Y

 

Punch

020037Y

 

Punch

Recommended products

AGIP GREASE PV2

 

Ivory smooth-textured,

slightly-stringy anhydrous calcium-base
grease.

TL 9150 066, NATO G 460 symbol

Rear

Suspensions

Vespa GTS Super 125 i.e.

SUSP - 200

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands