VESPA 2008 S 50 4T 4V Manual Download Page 53

Page: 53 / 199

Disconnect the connector on the flywheel cover

and measure the resistance between either con-

tact and the earthing.

Specific tooling

020331Y

Digital multimeter

PICK-UP CHECK

Specification

Desc./Quantity

1) Brown cable and earth

~ 170

Ω

STATOR WINDING CHECK

Specification

Desc./Quantity

1) Black cable and earth

~ 1

Ω

Ignition circuit

All the control operations of the system that require the disconnection of cables (checks of the connec-

tions and the devices making up the ignition circuit) must be done with the engine off: if this is not done,

the controls might be irretrievably damaged.

No spark plug

Once the lack of power to the spark plug has been

detected and the LED indicates it can be ignited,

follow this procedure:

- Check the Pick-Up.

Disconnect the electronic starter connector and

check continuity between terminal No. 3 (Green)

and terminal No. 4 (Black).

The check includes the Pick-Up and its power line.

If a break in the circuit is found, check again the

flywheel and the engine earth connectors. If non-

conforming values are measured, replace the

Pick-Up; otherwise, repair the cable harness.

Vespa S 50 4T 4V (2008)

Electrical system

ELE SYS - 53

Summary of Contents for 2008 S 50 4T 4V








































































































































































































Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands

VESPA 2008 S 50 4T 4V, Manual

Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands