VESPA 2008 S 50 4T 4V Manual Download Page 128

Page: 128 / 199

- Fit both dust guard rings «

» on the swinging hub

as shown in the detail drawing «

».

- Connect the swinging hub to the steering tube

with the guide pin, part 5*.

- Use the specific tool fitted with part 3* on its stem

and with part 4 at the bottom of the tool.

- Insert the previously greased pin on the swinging

hub and with the tool handgrip, move part 3 until it

stops on the steering tube.

- After fitting the pin, insert the two spacers, part

17*, slightly hitting with the mallet.

* Supplied with the tool

Specific tooling

020021Y

Front suspension service tool

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

- Lubricate the sealing rings with mineral oil and

half-fill the roller casings with grease.

- Insert the sealing ring on the pin and the roller

bushing with wedging washers at the same time.

- Remove the specific tool, then the part 5 (guiding)

partially ejected in the previous assembly stage;

leave part 4* always fitted.

- Replace part 3 with part 16* on the stem.

- Push, from the handgrip, the wedging washer -

roller casing - sealing ring unit, placing part 16 until

it stops on the swinging hub

- Repeat the operation described above using the

tool fitted with part 16 and part 22* instead of part

4 on the stem, on the side opposite the one shown

in the figure to refit the second wedging washer -

roller casing - sealing ring unit.

Suspensions

Vespa S 50 4T 4V (2008)

SUSP - 128

Summary of Contents for 2008 S 50 4T 4V








































































































































































































Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands

VESPA 2008 S 50 4T 4V, Manual

Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands