VESPA 2008 S 50 4T 4V Manual Download Page 84

Page: 84 / 199

Removing the timing system drive

- Temporarily loosen the tensioner central screw

and remove it together with the spring.

- Unscrew the 2 retainers indicated in the figure

and remove the chain tightener support being

careful to recover the sealing gasket.

N.B.

SHOULD THE GASKET NOT BE IN GOOD CONDITIONS,
REPLACE IT AFTER CAREFULLY CLEANING THE FAYING
SURFACE IN ORDER TO AVOID ENGINE OIL LEAKS

- Remove the driving pulley

- Remove the oil pump chain

- Remove the tappet cover

- Remove the central screw and the belleville

washer indicated in the figure and lock the cam-

shaft crown with the specific tool.

N.B.

TO FACILITATE REMOVING THE HEAD COMPONENTS,
SET THE CRANKSHAFT TO THE TIMING POINT (TDC OF
THE COMPRESSION END).

Specific tooling

020565Y

Flywheel lock calliper spanner

- Remove the camshaft control pulley and the washer below.

- Remove the pinion of the crankshaft timing control

- To remove the chain lower guiding pad, remove the head by pulling it upwards

N.B.

IT IS ADVISABLE TO MARK THE CHAIN IN ORDER TO ENSURE THAT THE DIRECTION OF RO-
TATION IS MAINTAINED.

See also

Removing the rocker-arms cover
Removal
Removing the driving pulley

Engine

Vespa S 50 4T 4V (2008)

ENG - 84

Summary of Contents for 2008 S 50 4T 4V








































































































































































































Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands

VESPA 2008 S 50 4T 4V, Manual

Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands