VESPA 2008 S 50 4T 4V Manual Download Page 91

Page: 91 / 199

- With the opening in the position indicated on the

tool, set the lock ring into position in the tool with

the punch.

- Rest the tool on the piston paying attention that

the 90°chamfered side faces upwards as indicated

in the figure.

- Fit the gudgeon pin stop using the plug.

CAUTION

USING A HAMMER TO POSITION THE RINGS CAN DAM-
AGE THE LOCKING HOUSING.

Refitting the piston rings

- Fit the oil scraper ring starting from the spring,

taking care that the spring ends do not superim-

pose. Fit the two piston rings so that their gaps and

that of the oil scraper ring are never aligned.

- Fit the 2nd sealing ring with the identifying letter

» facing towards the piston crown.

- Fit the 1st sealing ring with the reference letter

» facing towards the piston crown.

- Misalign the lining openings at 120° as shown in

the figure.

- Lubricate the components with engine oil.

N.B.

IN ORDER TO OBTAIN A GOOD BEDDING, THE 2 SEALING
PISTON RINGS ARE MADE OF CONE SHAPED CONTACT
SECTION TO THE CYLINDER. AS A RESULT IT IS IMPOR-
TANT TO RESPECT THE FITTING INSTRUCTION TO AS-
SEMBLY THE RINGS WITH THE "T" MARK FACING
UPWARDS.

Vespa S 50 4T 4V (2008)

Engine

ENG - 91

Summary of Contents for 2008 S 50 4T 4V








































































































































































































Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands

VESPA 2008 S 50 4T 4V, Manual

Search results

Summary of Contents for 2008 S 50 4T 4V

Reviews:

Related manuals for 2008 S 50 4T 4V

Brands by name

Popular brands