Z204998-0M
PAGE 1
©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected]
07121
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
TM
Power MoNITorING
INSTALLATIoN GUIDe
E30
Installer’s Specifications
Inputs:
Input Power
90-277VAC, 50/60 Hz
Accuracy:
Power/Energy
IEC 62053-21 Class 1, ANSI C12.1-2008
Voltage
±0.5% of reading 90-277V line-to-neutral
Operation:
Sampling Frequency
2560 Hz
Update Rate
1.8 seconds (both panels)
Overload Capability
22 kAIC
Outputs:
Type
Modbus RTU
Connection
DIP switch-selectable 2-wire or 4-wire, RS-485
Address
DIP switch-selectable address 1 to 247 (in pairs of 2)*
Baud Rate
DIP switch-selectable 9600, 19200, 38400
Parity
DIP switch-selectable NONE, ODD, EVEN
Communication Format
8-data-bits, 1-start-bit, 1-stop-bit
Termination
5-position depluggable connector
(TX+ TX- SHIELD TX+/RX+ TX-/RX-)
Mechanical:
Ribbon Cable Support
4 ft. (0.9 m) flat ribbon cable ships standard;
up
to 20 ft. (6 m) available
Environmental:
Operating Temperature Range
0° to 60°C (32° to 140°F) (<95% RH noncondensing)
Storage Temperature Range
-40° to 70°C (-40° to 158°F)
Altitude of Operation
3000 m
Agency Approvals
UL508, EN61010
* See Configuration section for details.
Panelboard Monitoring System
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices.
See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
• Only install this product on insulated conductors.
Failure to follow these instructions will result in death or serious injury.
DANGER
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
FCC PART 15 INFORMATION
NOTE: This equipment has been tested by the manufacturer and found
to comply with the limits for a class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Modifications to this product without the express authorization of
Veris Industries nullify this statement.
Product IdentIfIcatIon
E30
E30
CT Option
*Each strip contains 21 current sensors.
0 = 100A, 3/4" spacing
1 = 100A, 1" spacing
Description
A = Advanced
B = Intermediate
C = Basic
# of CTs
42 = 2 strips*
84 = 4 strips*
table of contents
Quick Install
2
Operation
2
Dimensions
2
Product Diagram
3
Data Output
3
Blink Codes for Status LED
3
Solid-Core CT Accuracy
3
Installation
4
Wiring
7
Configuration
8
Default DIP Switch Settings
8
Address Setup
9
Commissioning
10
Recommended Accessories
10
Safety
10
Troubleshooting
11
China RoHS Compliance Information IEFUP Table)
11
