background image

2

Ÿ

Do not place any items of clothing, hand towels or similar material over the  

      heater to dry. 
      This will cause risk of overheating and fire hazard.

Ÿ

Do not leave the heater unattended whilst in use.

Ÿ

Do not use this heater on a wet surface, or where it can fall or be pushed into 

      water.

Ÿ

Do not reach for an appliance that has fallen into water. Switch off at supply and 

      unplug immediately.

Ÿ

If the supply cord is damaged, it must be checked and repaired or replaced by the  

      manufacturer.

Ÿ

Do not operate appliance with wet hands.

Ÿ

Use this appliance only as described in this manual. Any other use is not 

      recommended by the manufacturer as it may cause fire, electric shock or injury.

Ÿ

Do not use abrasive cleaning products on this appliance. Clean with a dry rag. 

      Always remove plug from the mains supply before cleaning.

Ÿ

The heater must be installed at least 1.8 m above the floor

.

Ÿ

The heater must not be located immediately below a socket outlet. Socket outlet 

      should not be located at the back of the heater. It should be located outside 
      the physical footprint of the units to minimize heat build-up behind the heater.

Ÿ

The heater should be plugged in to the supply mains with an all-pole  

      disconnection mechanism with a breaker. The all-pole disconnection mechanism 
      must be installed on the height less than 1.8m from the floor.

Ÿ

The heater is to be installed so that switches and other controls cannot be    

      touched by a person in the bath or shower.

Ÿ

Do not connect the appliance to the mains source until it has been installed in its 

      final location and adjusted to the position it will be used in.

Ÿ

Do not operate with the cord coiled up as this could cause a build up of heat, 

      which could pose a hazard.

Ÿ

The use of an extension cord with this appliance is not recommended.

Ÿ

Do not allow cord to come in contact with heated surfaces during operation.

Ÿ

Children should be kept away unless continuously supervised.

Ÿ

The appliance is not intended for use by persons (including children) with 

      reduced physical, sensory or mental capabilities, or lack of experience and 
      knowledge, unless they have been given suppervision or instruction concerning 
      use of the appliance by a person responsible for their safety.

Ÿ

Children should be supervised to ensure that they do not play with the appliance.

Ÿ

The appliance is only intended for the purpose described in user manual.

Ÿ

Do not use appliance or any part of the appliance out of the intended use to avoid 

      risk.

Summary of Contents for Heatwave Series













Reviews: