VEMCO - VR2C Manual
9
Jul 2018
38
An example of a RTM Profile 0 session is shown below:
*450088.0#25,RTMPROFILE=0\r
*450088.0#25[0009],OK,#9A\r\n
*450088.0#25,RTMNOW\r
*450088.0#25[0009],OK,#9A\r\n
450088,000,2013-09-04 18:35:17,STS,DC=3,PC=25,LV=12.0,BV=3.6,BU=8.5,
I=2.4,T=23.4,DU=0.0,RU=0.0,XYZ=-0.03:-0.75:-0.63,#3F\r\n
450088,001,2013-09-04 18:35:22,A69-1601,179,#76\r\n
450088,002,2013-09-04 18:35:29,A69-1601,191,#78\r\n
450088,003,2013-09-04 18:35:35,A69-1601,179,#7C\r\n
450088,004,2013-09-04 18:35:41,A69-1601,191,#74\r\n
450088,005,2013-09-04 18:35:47,A69-1601,179,#81\r\n
450088,006,2013-09-04 18:35:53,A69-1601,191,#79\r\n
450088,007,2013-09-04 18:35:59,A69-1601,179,#86\r\n
450088,008,2013-09-04 18:36:05,A69-1601,191,#79\r\n
450088,009,2013-09-04 18:36:17,STS,DC=11,PC=89,LV=12.0,BV=3.6,BU=8.5,
I=2.3,T=23.4,DU=0.0,RU=0.0,XYZ=-0.03:-0.75:-0.63,#81\r\n
450088,010,2013-09-04 18:37:03,A69-1601,179,#77\r\n
450088,011,2013-09-04 18:37:09,A69-1601,191,#78\r\n
450088,012,2013-09-04 18:37:15,A69-1601,179,#7C\r\n
450088,013,2013-09-04 18:37:17,STS,DC=14,PC=115,LV=11.8,BV=3.6,BU=8.5,
I=2.4,T=23.4,DU=0.0,RU=0.0,XYZ=-0.03:-0.75:-0.63,#AE\r\n
RTM Profile 1 (Status Interval Block Output)
This profile outputs tag detection records on a schedule based on the status line interval. The
VR2C will output the status line followed by all the tag detection records received since the last
status line transmission. The default status line interval is 60 seconds, but it can be user
configured to any value between 1 and 65535 by adding
SI=x
to the command as shown in the
example below (which specifies a status line interval of 180 seconds).
Command:
*450088.0#25,RTMPROFILE=1,SI=180\r
Response:
*450088.0#25[0009],OK,#9A\r\n
In this profile, the VR2C transmits a “<” character before the output block and a “>” character
after the output block. The VR2C delays 100ms after transmitting the leading “<” to give the
monitoring device a chance to wake up the serial port if necessary.
RTM Profile 1 will not commence until an RTMNOW, RTM232 or RTM485 command has
been issued (which starts RTM).
An example of a RTM Profile 1 session is shown below:
*450088.0#25,RTMPROFILE=1\r
*450088.0#25[0009],OK,#9A\r\n
*450088.0#25,RTMNOW\r
*450088.0#25[0009],OK,#9A\r\n
<
450088,000,2013-09-06 19:14:14,STS,DC=7,PC=60,LV=12.0,BV=3.6,BU=8.5,
I=2.3,T=23.8,DU=0.0,RU=0.0,XYZ=-0.03:-0.78:-0.63,#45\r\n
>