Velocity Raptor RPTR155 Installation And Operating Instructions Manual Download Page 120

Page: 120 / 172

120

XII. Operation

F. Changing Adjustable Parameters (continued)

“Press”

button to access the following parameters:

Factory

Setting

Range / Choices

Parameter and Description

Enabled

Enable Disable

Central Heat Outdoor Reset Enable

If an outdoor sensor is installed and Outdoor Reset is Enabled, the boiler will automatically

adjust the heating zone set point temperature based on the outdoor reset curve in Figure

8. The maximum set point is defined by the Central Heat Setpoint [factory set to 180°F

(82.2°C)] when the outdoor temperature is 0°F (-18°C) or below. The minimum set point

temperature shown is 130°F (54.4°C) [adjustable as low as 80°F (26.7°C)] when the

outdoor temperature is 50°F (10°C) or above. As the outdoor temperature falls the supply

water target temperature increases. For example, if the outdoor air temperature is 30°F,

(-1.1°C) the set point temperature for the supply water is 150°F (65.6°C).
Disable Do Not Calculate setpoint based on outdoor temperature
Enable

Calculate the temperature setpoint based on outdoor temperature using a reset

curve defined by Low Outdoor Temp, High Outdoor Temp, Low Boiler Water

Temp, Min Boiler Temp and Central Heat Setpoint and Boost Time parameters.

0°F

(-18°C)

-40°F to 100°F

(-40°C to 37.8°C)

Central Heat Low Outdoor Temperature

The Low Outdoor Temperature parameter is also called “Outdoor Design Temperature”.

This parameter is the outdoor temperature used in the heat loss calculation. It is typically

set to the coldest outdoor temperature.

70°F

(21.1°C)

32°F to 100°F

(0°C to 37.8°C)

Central Heat High Outdoor Temperature

The High Outdoor Temperature parameter is the outdoor temperature at which the Low

Boiler Water Temperature is supplied. This parameter is typically set to the desired building

temperature.

110°F

(43.3°C)

70°F to 190°F

(21.1°C to 87.8°C)

Central Heat Low Boiler Water Temperature

The Low Boiler Water Temperature parameter is the operating setpoint when the High

Outdoor Temperature is measured. If the home feels cool during warm outdoor conditions,

the Low Boiler Water Temperature parameter should be increased.

130°F

(54.4°C)

80°F to 190°F

(26.7°C to 87.8°C)

Minimum Boiler Temperature (Central Heat and Auxiliary Heat)

The Minimum Boiler Temperature parameter sets a low limit for the Reset setpoint. Set this

parameter to the lowest supply water temperature that will provide enough heat for the type

radiation used to function properly. Always consider the type of radiation when adjusting

this parameter.

20 Minutes

0-1800 Seconds

(0-30 Minutes)

Central Heat Boost Time

When the Central Heat Setpoint is decreased by Outdoor Reset settings, the Boost Time

parameter is used to increase the operating setpoint when the home heat demand is not

satisfied after the Boost Time setting is exceeded. When heat demand has been “on”

continuously for longer than the Boost Time parameter the operating setpoint is increased

by 10°F (5.6°C). The highest operating setpoint from Boost Time is current Central Heat

Setpoint. A setting of 0 seconds disables this feature. Boost is not used when Sequence

Master is enabled.

Summary of Contents for Raptor RPTR155













































































































































































Search results

Summary of Contents for Raptor RPTR155

Reviews:

Related manuals for Raptor RPTR155

Brands by name

Popular brands

Velocity Raptor RPTR155, Installation And Operating Instructions Manual

Search results

Summary of Contents for Raptor RPTR155

Reviews:

Related manuals for Raptor RPTR155

Brands by name

Popular brands