manualshive.com logo in svg

Velleman HAA2890, Programming & Installation Manual

Share
Download
Velleman HAA2890 Programming & Installation Manual Download Page 30

30

APPLICATION EXAMPLE

                                                                                                                                                  

BASIC WIRINGS OF A STAND ALONE DOOR LOCK

NOTE:

Connect the 1N4004 as close as possible to the lock in parallel with the lock power terminals of the lock to absorb 
the back EMF to prevent it from damaging the keypad. The 1N4004 is not required if the electric lock is AC operated.

To avoid Electro-Static-Discharge from interfering with the operation of the keypad, always ground the (-) terminal 
of the keypad to earth.

 

12V DC

POWER
SUPPLY

AD-1312 
OR
AP-960

ELECTRIC LOCK

N.O. N.C.

OR

CATHODE

1N4004

OUTPUT RELAY

N.O. Output for 

Fail-secure Lock
N.C. Output for 

Fail-safe Lock

EGRESS
BUTTON

MORE EGRESS

BUTTONS CAN

BE CONNECTED

IN PARALLEL

N.O.

N.O.

THE WIRE HARNESS

HAA2890_Manual.indd   6

24/05/2012   15:21:12

Summary of Contents for HAA2890



































Reviews:

No comments

Brands by name

Popular brands

Load more brands