background image

Installation of Upgrade Kit

Safety Precautions

6

Figure 4.   Attaching the new CPU board/inner door assembly to the console

983-4.eps

1

1

2

3

1

Get the new TLS2P CPU board/inner door a

ss

embly 

from the kit. Get the two T-15 torx 

s

houlder 

s

crew

s

 

you removed from the right 

s

ide of the door earlier.

2

Get the static protecting wrist strap from the kit and slip 
the looped end around one wrist and connect the other 
end to side of the console.

3

Remove the CPU board/inner door assembly from its 
packing and push the ground cable and ribbon cable 
through the right side opening in the inner door 
assembly and place the inner door assembly on the 
console and screw in the two right-side T-15 torx 
shoulder screws (item 1 

in Figure 4

), snug but not tight. 

Reattach the grounding strap to the bare metal on the 
top of the inner door.

4

Loosen the ground wire saddle clamp on the inner door 
(item 2 

in Figure 4

) and loop the ground wire through it 

and tighten securely (see photo at right). The other end 
of the ground wire will attach to the new door’s 
grounding saddle clamp.

5

Connect the ribbon cable (item 3 

in Figure 4

) to the 

connector on the left side of the new CPU board.

Summary of Contents for TLS2














Reviews: