background image

Site Prep - International Installations

TLS-IB Location

2-4

TLS-IB Location

The TLS-IB should be located on an inside wall of the forecourt building Be sure the console will be protected 
from vibration, extremes in temperature and humidity, rain and other conditions that could cause equipment 
malfunction.

The equipment is designed to operate safely under the following range of conditions:

• Altitude up to 2000 m.

• Temperature range of 0 to 40°C.

• A maximum relative humidity of 95% RH (non-condensing) at temperatures up to 40°C.

• Main supply voltage fluctuations not exc/- 10%

• Pollution Degree Category 2 Installation Category II

The TLS-IB unit must be installed within the interior of buildings.This unit is not suitable for 
any external location.

Ensure that the TLS-IB is located where neither it nor its associated cabling will be damaged by doors, furniture, 
barrows, etc. Consider the ease of routing wiring, ducting and probe cables to the unit.

Overall dimensions and weight of the TLS-IB are: height - 163 mm, width - 188 mm, depth - 50 mm, weight - 1.8 
kg.

To allow for maintenance ensure that the console is in an accessible area, even when the console doors are open.

If the unit requires cleaning, do not use any liquid materials (e.g. cleaning solvents). It is recommended that the unit 
be wiped with a clean dry cloth when necessary.

Ensure that all relevant subcontractors and other personnel are aware of the selected location.

The TLS-IB is installed by Veeder–Root authorised engineers.

TLS-IB power must come from a dedicated circuit via a fused, switched, neon indication spur within 1 metre of the 
console position. The spur must be clearly marked to identify it as the means for disconnecting the console. Input 
power must be a 24-hour clean supply. A typical installation is shown in Figure 2-2.

WARNING

An explosion could occur if other wires share ducts with intrinsically safe 
probe wiring. Ducting from probes must not contain any other wiring circuits.

FAILURE TO COMPLY WITH THIS WARNING COULD RESULT IN EXPLOSION, 
DEATH, SERIOUS PERSONAL INJURY, PROPERTY LOSS OR EQUIPMENT 
DAMAGE.

NOTICE

Summary of Contents for TLS Series

















































Reviews: