manualshive.com logo in svg

Varian TriScroll 300 Series, Maintenance Manual

Share
Download
Varian TriScroll 300 Series Maintenance Manual Download Page 68

58

TriScroll 300 Dry Scroll Vacuum Pump 

 D

R

A

FT 

4/

29

/0

4

8. Immediately, while the orbiting plate is still 

hot, place the orbiting plate onto the post of 
the orbiting plate fixture that has the larger 
bottom disk. 

9. Place the large seal and the locking nut onto 

the post and tighten the entire assembly.

10. Allow the orbiting plate to air cool 

completely. 

11. Once it is cooled, remove the orbiting plate 

from the orbiting plate fixture.

12. Replace the seal and tighten the nut onto 

the orbiting plate fixture.

Install the Wave Washer and Shaft Seal

Tools required:

❑

Allen wrench

❑

Arbor press

❑

Seal installation tool

❑

Krytox GPL 224 grease

❑

Loctite 242

Locate the following parts:

➀

Wave washer - nested

➁

M5x5 set screw (6)

➂

Shaft seal, 24x32x4, included in 
maintenance kit

Orbiting Plate Assembly (continued)

WARNING

Assembly is hot, use heat 
resistant gloves.

2

3

1

Summary of Contents for TriScroll 300 Series





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands