Vari Hurricane MaX F-580, User Manual

Page: 27 / 64

Hurricane MaX

When starting the engine, both control levers ( 15 and 17 in
Fig. 2) must be in their OFF position (they must
not be pressed to the handles)!

Some engines may feature a fuel valve in their fuel supply to the carburettor! Do not forget to open the
fuel supply, please.
The following chapters describe the individual basic differences in starting. The accelerator lever positions ( 1 = STOP , 2 = MIN ,
3 = MAX , and 4 = CHOKE ) are described in Fig. 5 . All the four main positions described are locked by a simple, dip-protrusion system in
the lever body. The functions of the individual switch buttons ( STOP , 1 and START ) on the start panel are described in
Fig. 4
.
2.4.2.1.1 E
LECTRIC
S
TARTER
E
NGINE
Modern and also the easiest way of engine starting. The battery also serves as a key to the machine and is also a safety device against
any accidental engine start.

The engine cannot be started without a properly inserted battery in its holder at the top of the engine.

The engine cannot be started with a dead 69 battery.

The engine features a fixed operating speed and does not idle.

Before every engine start, check the connector cables and condition of the cable harness that leads from the
starting panel to the engine.
1. Fig. 4 - On the starting panel, there press the middle button marked 1 .
2. Press the right button marked START and hold it for max. 5 seconds, till the electric starter starts the engine 70 , then release
the button.

Do not try starting an already running engine! You may destroy the starter.

Do not leave the machine unattended!
2.4.2.1.2 M
ECHANICAL CHOKE ENGINE
1. Move the accelerator lever per Fig. 5 to its position 4 CHOKE .

Start an already warm engine with the accelerator lever in its 3 MAX position.
2. Start the engine by pulling on the hand starter cord 71 .
3. Let a new or cold engine run for about 30 seconds with the choke engaged (accelerator lever in its 4 CHOKE position ), then
move the accelerator lever to 3 MAX .

Do not leave the machine unattended!
2.4.2.1.3 A
UTOMATIC CHOKE ENGINE
1. Move the accelerator lever per
Fig. 5
to its position 3 MAX .
2. Start the engine by pulling on the hand starter cord 72 .
3. The automatic choke, once the engine is warmed up 73 , will adjust the engine speed.

Do not leave the machine unattended!
2.4.2.2 W
ORKING TOOL START

Prior to every use of the machine, check the tightening of the bolts fastening the work attachment and also all
the bolt joints of the safety elements, covers, and engine!

Make sure all the persons, children, and animals are located at a SAFE distance from the machine! Otherwise, do
not continue in any future activity!
1) Start the engine 74 . If the engine is cold, let it warm up at its maximum speed for approx. 1 minute.
2) Grab the left handle of the handlebar with your left hand. With your right hand move (lift), following
Fig. 7
, the right control
lever 1 to its upper position, so it is fully inserted into strap with cables 2 .
3) Press locking device button 3 on strap with cables 2 in the arrow direction. Hold the button till the control lever moves
downwards to the handle and locks ( Fig. 8 ) and starts moving the strap with cables.

Slowly push the lever approximately two-thirds of its travel, so the working tool can start spinning, and
the engine does not stop.
4) Once the working tool starts spinning, push the lever fully to the handle, to its working position (
Fig. 9
), and hold it firmly.
69 Battery charging is described in the engine operating instructions.
70 Wait for 1 minute between start cycles.
71 The engine startup instructions are described in detail in the engine operating instructions.
72
The engine startup instructions are described in detail in the engine operating instructions.
73
Depending on the ambient temperature and engine temperature, the automatic choke is activated for about 1 minute.
74
The engine startup instructions are described in detail in the engine operating instructions.
27
Re
vi
ze
1
0/
20
19