PJXP200 / PJGCVX200 / PJCV224
Before each use of the machine
check if any of its parts (especially the working mechanism or its casing) are not damaged or
loose.
Discovered defects must be rectified immediately!
For repairs use only original spare parts.
Before proceeding with work with any operating machines of the system, check the function of the engine safety shutdown with a
switch on the left handlebar handgrip of the engine unit. The function of the safety switch is described in the text.
When working with the machine use only the second position of the safety ignition switch.
Do not start the engine if its not attached to the gearbox! Do not remove the driving unit from the gearbox while the engine is
running!
Pay increased attention when handling the driving unit - after the engine has been switched off the exhaust silencer remains hot!
Make sure that there are no leakages and spills on engine parts when refuelling! Should that happen dry the stained parts or wait
until the petrol evaporates.
Use caution when attaching, removing or transferring the driving unit to another machine! The exhaust silencer remains hot for
certain time after the engine has been switched off! When attaching or removing the driving unit approach it from the left side, i.e.
from the side of the air cleaner on the engine.
Use caution when closing and releasing the quick-operating clamps! The springs have a great pull and considerable force is required
for connection or disconnection. Your fingers can be injured!
If you are not attaching the driving unit on another machine never put it on easily ignitable materials. The high operating
temperatures could cause a fire!
Do not start the engine in enclosed spaces! Exhaust fumes contain poisonous substances that can cause loss of consciousness and
death.
Attention! The machine is fitted with an automatic centrifugal clutch. At speeds above the minimum the energy will always transmit
to the gearbox. Hence do not start the engine with engaged gear but keep it always in the neutral gear “0” or use starting aids! On
adapters with active accessory drive always turn off the drive of the working implement!
Engage gears on adapters with mechanical multistage gearboxes only when the engine is idling and with the machine standstill!
Never adjust the handlebar position when the machine is moving! There is a danger of loss of control over the machine with the
possibility of danger to health or property of the operator or other persons!
Before starting any activity near the machine, always turn off the engine and wait until the working implement stops working!
Before leaving the machine, always turn off the engine!
It is forbidden to remove any protective devices and covers from the machines.
With respect to the exceeded recommended values of noise and vibrations, observe the following instructions when working with
the machine:
1. Protect your hearing by using suitable protective aids according to
ČSN EN 352-1
(
ear mufs
) or
ČSN EN 352-2
(e
ar plugs).
Request these aids from your dealer.
2. Take at least 10 minute long breaks after each 20 minute work with the machine. At these breaks the operator must not be
exposed to other sources of noise or vibration.
During work wear work aids approved in accordance with
ČSN EN 166
or
ČSN EN 1731
(tight clothes, sturdy shoes, working
gloves and safety goggles). Keep a safe distance from the machine given by handles.
Do not use the machine on a wet surface. You must always move on safe ground. Walk during work, never run. Be particularly
careful when changing direction on slopes. Do not work on heavily sloping hills. If you fall, do not hold onto the machine but
release it.
Maximum tilt of the engine during work: long-term 20°, short-term
30°. Observe the maximum permissible - safe - climbing
accessibility - during work.
All repairs, adjustments, greasing and cleaning are to be carried out when the machine is at standstill with disconnected spark plug
cable.
Observe basic hygiene rules, regulations and legislative acts on environmental protection when working with lubricants and when
you washing the machine.
2.2.2 Noise and vibration values
The noise and vibration values of machines and adapters for which they are intended are always listed in the instructions for use.
2.2.3 Safety pictographs
User is obliged to maintain the pictographs on the machine legible and ensure their replacement in case they are damaged.
28
Short term = up to one minute.
17
R
ev
is
io
n
1
0
/2
0
2
1
