background image

Vante

® 

Model 4600 

 

 

13 

 

Completed seal 

PUSH tubing to 
next seal position 

Lift tubing off seal trigger 

 

Figure 2.9  Repeating the Seal Process 

WARNING

:   

Be  sure  to 

push

  the  tubing  through  the  sealing  region  to  the  next 

position.    Under 

no

  circumstances  should  the  tubing  be  separated  by 

pulling  it  at  the  instant  of  sealing.    An  opening  in  the  tubing  may 
occur,  which  will  subject  the  media  to  non-sterile  conditions  and  the 
user to potentially hazardous fluids.  In addition, the Sealing Head may 
become  damaged  by  arcing  caused  by  contamination  of  the  sealing 
region. 

Seal spacing must be in accordance with the guidelines specified in Section 2.4.  

WARNING

Multiple seals spaced less than the recommended distance may cause a 
rupture of a sealed tubing segment. 

NOTE:

 

The Power Source is equipped with a thermal protection switch to prevent 
the equipment from becoming damaged.  If thermal cutout is reached, the 
power  source  will  not  work  for  several  minutes  until  the  temperature  of 
equipment lowers.  

WARNING:

   

If  you  observe  arcing  while  making  a  seal,  follow  the  instructions  in 
the  Troubleshooting  Guide  section  under  “Arcing  or  Bad  Seals.” 
Although  a  seal  made  when  you  experience  arcing  may  look 
acceptable,  it  may  be  inadequate.    Take  precautions  as  if  this  is  an 
inadequate seal. 

WARNING

:   

The Power Source is designed for rapid sealing applications; however, 
extreme heavy duty use may result in thermal build up in the jaw area 
which  can  cause  poor  seal  quality  or  tubing  ruptures.    If  you  should 
experience these problems, reduce the rate of sealing, as necessary, or 
allow for periods of rest for the Sealing Head. 

 

Summary of Contents for 4600


































Reviews: