background image

Vante

® 

Model 4600 

 

 

2.

 

Power Source Operation 

2.1

 

Setup 

Remove the components from their protective shipping containers and visually inspect 
them for obvious damage.  Contact an authorized Vante service center if any damage is 
found.  If possible, retain shipping containers and packing materials for future use. 
 
Connect the AC power cord to the power input receptacle located on the rear of the 
Power Source.  Refer to the voltage/fuse plate located on the back of the unit to 
determine the appropriate AC power input.  The Power Source must be 100, 120 or 230 
VAC, 50/60 Hz as indicated on the rating plate. 

NOTE:

 

Check  to  see  that  the  power  cord  plug  matches  the  power  receptacle  for 
the  country  in  which  the  Power  Source  is  being  used.    If  it  does  not, 
contact an authorized Vante service center. 

 
Place the Power Source on a desk or lab counter for convenient use and route the AC 
power cord to prevent interference with other equipment or activities. Verify the AC 
power switch is in the 

"

"

 (off) position and connect the AC power cord to the AC 

power receptacle.  
 
When using the Power Source with a Hand Held Sealing Head, attach one end of the RF 
power cable to the Power Source and the other end to the sealing head.  Connect the cable 
by pushing the connectors together and rotating clockwise until locked (see Figure 2.1). 

 

Model 4600

 

Model 4105 
Sealing Head

 

 

Figure 2.1  RF Power Cable Attachment (For Use with a Model 4105) 

CAUTION:

  Do  NOT  attempt  to  use  any  other  length  or  type  of  RF  power  cable. 

Unauthorized  substitution  of  the  RF  power  cable  may  result  in 
malfunction of the Power Source and will void the warranty! 

 
When using the Bench Top Sealing Head, connect the BNC connector end of the Bench 
Top Sealing Head to the RF output on the back of the Power Source.  Rotate the 

Summary of Contents for 4600


































Reviews: