background image

19

T

roubleshooting

TROUBLESHOOTING PROCEDURES FOR VSU, VPL AND VCR

Issue

Cause

What to do

After installation, 
the unit doesn’t 
work.

1.  The power source is not turned ON.

1.  Make sure the circuit breaker and the unit’s 

power is ON.

2.  The power line and the cable locking connector 

is not connecting properly.

2.  Check the power connection with the unit is 

connected properly.

3.  The switch board and control board wirings are 

disconnected.

3.  Make sure the wirings between the switch 

board and control board are connected 
properly.

4.  The switch board or control board is defective.

4.  Change the switch board or control board.

Light works, 
but motor is not 
turning.

1.  The motor is defective, possibly seized.

1.  Change the motor.

2.  The thermally protected system detects if the 

motor is too hot to operate and shuts the motor 
down.

2.  The motor will function properly after the 

thermally protected system cool down.

3.  Damaged capacitor.

3.  Change the capacitor.

4.  The switch board or control board is defective.

4.  Change defective part.

The unit is 
vibrating.

1.  The motor is not secured in place.

1.  Tighten the motor in place.

2.  Damaged blower wheel.

2.  Replace the blower.

3.  The hood is not secured in place.

3.  Check the installation of the hood.

The motor is 
working, but the 
lights are not.

1.  Defective halogen bulb.

1.  Change the halogen bulb.

2.  The light bulb is loose.

2.  Tighten the light bulb.

The hood is 
not venting out 
properly.

1.  The hood might be hanging to high from the 

cook top.

1.  Adjust the distance between the cook top and 

the bottom of the hood within 28” and 36” 
range.

2.  The wind from the opened windows or opened 

doors in the surrounding area are affecting the 
ventilation of the hood.

2.  Close all the windows and doors to eliminate 

the outside wind fl ow.

3.  Blockage in the duct opening or ductwork.

3.  Remove all the blocking from the duct work or 

duct opening.

4.  The direction of duct opening is against the wind.

4.  Adjust the duct opening direction.

5.  Using the wrong size of ducting.

5.  Change the ducting to at least 6” or higher

Metal Filter is 
vibrating.

1.  Metal fi lter is loose.

1.  Change the metal fi lter.

Summary of Contents for VSU-E30AS
























Reviews: