background image

11

1.  Measure from range top to hood bottom and mark line A.  

(26” minimum from range top) .

2.  Plum and mark center line.

3.  Mark mounting height line B. (12” from line A)

4.  Mark mounting spread from C/L on line B. From center 

line to left mount mark (3-1/2”). From center line to right 
mount mark (2”). 

5.  Fasten (2) M4x1-1/4” screws into studs on line B.  Do not 

fasten screws all the way.  

Note: wood blocking may 

need to be added behind the drywall if no studs are 
present.  Wall anchors may also be used but check 
local codes for compliance. Failure to use suitable 
wall anchors and screws to hold the weight of the 
hood could result in personal injury or damage to 
cooking sureface or counter.

6.  Hang hood onto screws and hand tighten. (Fig.A)   Use 

the last M4x1-1/4” screw to further secure the hood to 
the wall from inside the hood.

7.   Center and attach duct cover bracket to wall below 

ceiling or soffi t using (2) M4x1” screws.

8.   Install electrical.

9.   *Install duct work and duct tape.

10. Power up hood and check for leaks around duct tape.

11.  Place telescopic duct covers onto hood and extend 

inner (top) duct cover upwards and secure to duct cover 
bracket using (2) M4x3/8” screws.                                       

      *if using hood in recirculating mode you must secure air 

diverter plate onto wall before installing duct work and 
duct covers.  Turn to page 14 for more details.

A

B

C/L

12"

C/L

26" min

fig. A

Duct Cover Bracket

2"

3-1/2"

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.

!

Cable Lock

Cable Lock

A cable locking connector (not supplied) might 
be required by local codes.  Check with local 
requirements and codes, purchase and install 
appropriate connector if necessary.

CAUTION: At least two installers are

required due to the weight and size of the
hood.

!

Installation – 

Mounting the Hood VSU

Summary of Contents for VSU-E30AS
























Reviews: