background image

3.5.

Audio Adjustments

There are two potentiometers on the V-9982 system allowing the user to tailor the audio out-
put level and high frequency response.  These potentiometers are located on the front side of
the device directly above the audio output connectors.

3.5.1.

Audio level

The level of both the LINE OUT and SPKR OUT are simultaneously adjusted using the audio
level adjustment potentiometer.  Turning this potentiometer counter clockwise will lower the
audio level.  Turning this potentiometer clockwise will raise the audio level. 

3.5.2.

Aphex®

This special, psycho-acoustic processing extends the high frequency response of the V-9982.
Turning this potentiometer clockwise amplifies the high frequencies while turning it counter
clockwise attenuates the high frequencies.

3.6.

Connections

There are several connectors on the front side of the device.

DC Power

2.5mm Barrel connector. The system is powered by 12VDC.  Use only the AC-DC power
adapter supplied by the manufacturer to guarantee proper operation.

Line Level Audio Output(LINE OUT)

RCA connector. A 600 ohm, transformer isolated, audio output.  When installing the V-9982
system, connect this output to the phone system first.  

Amplified Audio Output(SPKR OUT)

RCA connector. An amplified, 1.5 watt into 8 ohm, audio output.   Use this audio output if the
audio from the Line output can't drive the on-hold circuit to a high enough level.

4. POWER FAILURE RECOVERY

The V-9982 uses FLASH memory which is not dependent upon power or battery backup to retain
its memory. This eliminates problems associated with brown outs or unexpected power losses.
When power is returned, the system will immediately start the operation it was in prior to power
being removed.

1.

When the system is not recording, the button functions as an Eject button.  

2.

When the V-9982 is recording audio, (whenever the Record LED is on) pressing this
button momentarily will stop the recording and save the audio which was just record-
ed.  The system will rewind the tape, but not eject it.

3.

If the button is pressed momentarily while the V-9982 is recording audio, and then
pressed momentarily again, the system will stop the recording process, save the audio
just recorded, and eject the cassette tape.

4.

If this button is pressed and held for two seconds while the V-9982 is recording, the
audio just recorded will be deleted, and the tape will be ejected without being
rewound.

3.3.2.

Speaker pushbutton

A locking pushbutton, black in color, which controls the monitor speaker located on the
front of the unit. Pressing this button will activate the monitor speaker, allowing the local
user to hear the audio being output by the V-9982.  Releasing the button will deactivate the
monitor speaker.  

The volume of the monitor speaker is determined by the volume setting of the audio output.
If the phone system requires a particularly low level from the V-9982, the volume of the
monitor speaker will also be low.

Note:

Do not adjust the audio output level adjustment in order to hear the monitor speaker

level better.  Doing this will adjust the level of the Message-On-Hold output which may not be
acceptable.

3.4.

LED (Light Emitting Diodes) Descriptions

Three LEDs are provided on the top of the V-9982 unit to display the current status of the
system.

Eject LED

This yellow LED will light whenever there is no tape inside the system.  When a tape is insert-
ed, and loaded into the machine, this LED will go out.

Record LED

This red LED will light when the V-9982 starts recording an audio program, and will go out
when the recording process stops.  The Record LED will blink one time when the V-9982 is
powered on, indicating that the memory is operational.

MOH LED

This green LED will light when the V-9982 is playing a previously recorded message.

10

V-9982 Owner’s Manual

V-9982 Owner’s Manual

7

Summary of Contents for V-9982









Reviews: