3. OPERATION:
3.1.
Message Downloading:
When you receive the new V-9982 MOH system, its memory will be blank. To load a new mes-
sage into the V-9982's memory, simply insert a recorded cassette (Tape Up, Facing Label).
When a new tape is inserted, the V-9982 will automatically rewind the cassette to the begin-
ning and then start playing it. The V-9982 will record the audio program, ignoring the
silence before and after the audio recorded on the cassette. When the audio program on the
tape starts, the red Record light will come on signifying that audio is being recorded to mem-
ory. At the end of the audio program, when the V-9982 detects 5 seconds of silence, the
recording will end, the Record LED will go out, and the system will automatically rewind the
cassette tape. The 5 seconds of silence will be deleted prior to playing the message.
The audio being recorded will be output through the LINE and SPKR outputs during the record-
ing process. This audio may also be monitored by the user, by pressing the "Speaker" button.
Warning: When a tape is inserted into the V-9982 system, the previous recording
is deleted immediately. If the tape is then ejected, prior to recording any audio,
the V-9982's memory will be empty.
3.2.
Message Playback:
After a message has been recorded into memory, the V-9982 will automatically begin playing
this message through the audio outputs. The green M-O-H LED, will illuminate whenever a
pre-recorded message is playing.
3.3.
Pushbutton Descriptions:
Two pushbuttons are provided on the V-9982 system.
3.3.1.
Eject / Record Stop Pushbutton
A momentary pushbutton, red in color. This button allows the user to stop the recording
process, and/or eject the tape.
5. TROUBLESHOOTING GUIDE
No LEDs are active on the V-9982.
•
Just after a tape is inserted, and before audio is detected by the V-9982, all LEDs will be off.
•
Verify that the AC-DC power adapter is plugged into non-switched AC power outlet.
•
Verify that the power connector is plugged completely into the jack on the V-9982.
The system will not mechanically load the tape into the system
•
Push the cassette tape completely into the V-9982.
•
Verify that the AC-DC power adapter is plugged into non-switched AC power outlet.
•
Verify that the power connector is plugged completely into the jack on the V-9982.
The Record LED never comes on after the cassette tape is loaded into the system
•
Verify that the tape was inserted right side up.
•
If the tape is blank, the Record LED will never come on.
•
Verify that the nominal level of the audio recorded on the tape is over -20dB.
After recording the tape, the tape ejected, and the system is not playing a message.
•
If the user pressed, and held the edit/eject button during the record, the system will eject
the tape immediately and delete the recorded audio.
•
Verify that the tape was inserted with the audio recorded side facing side up.
•
If there is no audio on the tape, it will eject it automatically when it reaches the end of the
tape.
Cannot hear anything through the on-hold circuit
•
If both Record and MOH LEDs are off, there is no audio being output by the system.
•
Verify that the RCA to RCA connector is securely attached to the V-9982 and the phone sys-
tem.
•
Turn the output level adjustment clockwise to increase the audio output level.
•
Use the 8 ohm output instead of the line level output.
Cannot hear anything through the monitor speaker
•
If both Record and MOH LEDs are off, there is no audio being output by the system.
•
Press the Speaker button so that it locks in the depressed position.
•
If the level of the audio output is adjusted very low, the level from the monitor speaker will
also be very low.
6
V-9982 Owner’s Manual
V-9982 Owner’s Manual
11
